Rust-Oleum7779502 Stops Rust Brush On Paint, Quart, Gloss Black, 32 Fl Oz (Pack of 1)

Good quality paint . I paid a little more for the convenience of having to open a small can and “ use it up “ and not have a large ( opened can “ go bad before I can use it . 🤔🤷‍♂️

The paint works as it should. The color was accurate. The coverage was accurate and so it was the texture.

Paint is an oil based . Mineral spirits is needed to thin and clean brush

Not great for walls. Spreads oily and peels when dries.

I generally don't like oil-based paint because it's harder to clean up, and haven't really used much since painting models as a kid.I had some of the same issues with this paint as I did with Testors back in the 1990s: Paint goes on too thick, details of small items lost, long drying time. The main issue there, I've discovered, is that the paint goes on thick, but does spread and "settle" well when using a larger amount. So for larger items, it's probably more ideal, if you're okay with the finish.After some failures and second attempts on boot lacing hardware, I found a good method to get the results I wanted. It's mainly just following a certain procedure to get there. My goal is to paint SOME of the boot hardware, but not all, which means getting a finish which mostly matches the paint already applied. This is more matte semi-gloss.Have mineral spirits or acetone handy to rinse your brush, as the paint in the brush will start to dry, get sticky, and make the paint much harder to apply uniformly. I didn't bother at first with rinsing and ended up using brake cleaner, which isn't stated in the directions, but works well enough while the mineral spirits are on the way. Feel free to thin the paint according to the instructions if necessary to get it to go on more smoothly, as it does have a tendency to goop up on items with fine detail.I found one of the keys to getting a smooth finish with this is to apply at least two THIN coats. I think a lot of people (including myself) tend to try to go for opaque coverage with one coat and try to finish quickly, and it just doesn't work when painting small items... it just ends up looking cakey and bad when dry. From what I have seen, if the paint is shiny when you're done applying it, it's probably going to dry that way. As always, apply the first layer uniformly with coverage, but do not worry about it being sheer, because at least one more thin coat is necessary.It does take around 24 hours to be sure it dries completely so that it's not sticky and you don't fingerprint the finish. Just allow more time for your project, and it definitely helps. As you apply it though, the somewhat slower drying time can work to your advantage. If you apply, wait a few seconds for some paint to stick, and keep brushing with a dryer brush, you can remove excess paint that would dry shiny. This sometime tends to "settle" in a way that doesn't look smooth, so you can move on to another piece for a couple of minutes and check your previous piece to make sure it's completely smooth. If not, brush without applying more paint again to smooth the surface until enough paint has stuck to the surface and the surface of the paint is smooth and more matte, if that's what you're going for. Wait 24 hours and repeat this process.Again, if your results still turn out gloppy, sticky-looking and too shiny, thin the paint slightly with mineral spirits or acetone and apply many thin coats to make sure you can apply it without the paint collecting in crevices and corners of your piece. If I was using this sort of paint on a small or medium figure, for example, I would probably thin it to the maximum directed and apply as many coats as necessary to get the result I wanted.If you have something which you can spray freely with some or no masking, using a good paint gun to get get uniform coverage would probably be ideal, but again, this paint is more on the shiny side when a lot of it is applied. If I had to do this project again, I would most likely use this same paint, as I would still be going for a thin and smooth finish. Using a matte finish paint with the same viscosity might be easier, but avoiding pooling of excess paint would still be something I would want to minimize.

Sometimes you need more coverage then the spray can give you

Can't go wrong with good paint !!!

⭐️⭐️⭐️⭐️⭐This brown Rust-Oleum paint is *aggressively* brown. Like, it’s not just brown—it’s the kind of brown that makes you question your life choices. I bought it to paint my tin roof, that was sad and rusty. and Now my house looks like it’s wearing a giant brown mushroom. It’s not ugly, per se, but it’s definitely judging the neighborhood.The coverage, though? Fantastic. One coat and my roof went from “rusty eyesore” to “I might be made of chocolate.” It’s so smooth and even that I almost forgot I was painting, not frosting a giant cake. The only downside is that now everything around my house looks like it needs a coat of this paint. My shed? Brown. My mailbox? Brown. The dog house? Brown.In conclusion, if you’re looking for a paint that’s reliable, durable, and the color of a wet tree trunk, this is it. Just be prepared for your property to slowly turn into a sepia-toned movie set. 🟤🤎🟤🤎