G.hn Ethernet Over Coax Adapter Kit - 1.2Gbps Network for Unused/Dark Coax - Secure Wired Connection for Gaming & Streaming - Easy Setup - Not for Cable TV/Internet - 2 Units (GCA-1200-KIT)

I'm happy with the coax to ethernet adapter. A pretty short run of coax from my basement to the 1st floor allowed me to get 650+Mbps on that link. Not too bad!

This was perfect and works. Just what I wanted

THIS SEEMS LIKE JUST A REBRAND OF OLD COMTREND G.HN WHICH WAS GOOD.I have cable internet. This product is not the best suited one if I had just added the connectors everywhere in my house.So I had to go to my attic and isolate the incoming internet coax from the other ones in my house.I had to put 1-3(explained later) extra cables from my attic to my router.That was easy as my router is very close to my attic.But this saved me the extra ethernet wiring I would have to add.At first I isolated the incoming coax so that it directly goes to my router.METHOD 1 (not recommended but cheaper):NLC == Nexuslink/Comtrend converterRouter(WAN PORT) -- COAX0 ---1-1 Coax Connector COAX1 form CABLE INTERNET from PROVIDERRouter(LAN PORT) -- Ethernet -- NLC -- COAX2 -- SPLITTER -- COAX3 ------ NLC -- TV-- COAX4 ------ NLC -- Access Point-- COAX5 ------ NLC -- Switch -- Laptop/DesktopsI added 1 coax from router to attic. This coax was connected via splitter to all other coax in my house.Then I added converters to all end points.Thus creating a mesh of coax with this converter at all ends, one of which is attached by ethernet to router.This seems to work quiet well and my latency reduced quiet a lot.At some endpoints I even connected switches or Access points. Everything was fine (very good infact) till I replaced Access points at some endpoints with mesh nodes (ethernet backhaul).Mesh nodes were constantly dropping. To fix this and only this i went to method 2METHOD 2:NLC == Nexuslink/Comtrend converterRouter(WAN PORT) -- COAX0 ---1-1 Coax Connector COAX1 form CABLE INTERNET from PROVIDERRouter(LAN PORT1) -- Ethernet -- NLC -- COAX2 -- 1-1 Coax Connector -- COAX3 ------ NLC -- TVRouter(LAN PORT2) -- Ethernet -- NLC -- COAX6 -- 1-1 Coax Connector -- COAX4 ------ NLC -- Mesh Node 1Router(LAN PORT3) -- Ethernet -- NLC -- COAX7 -- 1-1 Coax Connector -- COAX5 ------ NLC -- Mesh Node 2I I added 3 coax cables fron router to attic.Each of these new cables connected 1 on 1 to each endpoint in my house.So one side of each of these 3 links were connected to converter and then to router while the other sides to mesh nodes.This created an effect of having put a dedicated ethernet cable to each endpoint.This method works best and has the best throughput but is obviously expensive and difficult to achieve.

Unfortunately these NexusLink IP-over-coax solutions did not work in our application offering very slow transfer speeds. However technical support was very responsive, and upon further review we determined that the issue we were having was due to the venue's (the location we were installing at) existing low quality low-voltage infrastructure. And we indeed verified this when testing the products back on our test bench, where they showed great speeds close to gigabit. So we would use again but only in venues where we had control/installed for ourselves the low-voltage infrastructure. A bit of advice I would set up/"pair" the devices prior, then test to ensure they are what you need, prior to deploying in the field.

anteriormente tenia un IP Over coaxial de la marca eKL, luego tuve otra marca generica que me daba a lo ultimo de su vida util 10 Mbps.tengo que decir que donde esta el Modem del IPS, esta a unos 650-700 metros de distancia.ahora con estos me da velocidades de 50-90 Mbps.dependiendo del dispositivo desde donde reaice la prueba.segui las recomendaciones de uno de los comentarios, de emparejarlos primero con un cable corto y luego colocarlos en su posicion final, y listo.actualizo la info,la verdad estoy mas q satisfecho, cambie mi router AC1200 con puerto WAN de 100Mbps por uno AX1500 con puerto WAN 1000Mbps y tengo conexion de 400Mbpsmas que recomendado

So I bought this product in hopes of having an additional ethernet connection available for my PS5. I hooked it up like the instructions stated, and it worked for a few minutes. Then my after about an hour my internet connection went out. I called customer service, they sent a technician out and he said someone had disconnected my internet connection from the outside. We both found that strange but shrugged our shoulders. I showed him this product he was skeptical, and told me he had never heard of it. He also said it might interfere with my internet, and he would not advise me to hook it up. I went ahead and hooked it up again, and everything was working fine. About 30 minutes later the internet went down again, and there was a knock at my door. It was ANOTHER Xfinity representative who said that he asked me was I a customer and what did I have in my house. I told him about this product what it is used for etc. He was like yeah don't hook that up anymore. It is affecting the whole neighborhood. Everyone's cable and internet is screwed up and this device is the culprit. I said um okay. So this device does not play well with Xfinity and it does shut down the neighborhood.

In one location of my house, I have only one Cat6 but needed to run two devices on separate networks.It is on the first floor of a two story house so running another cable was problematic.I had been using smart switches and VLAN's but was always experiencing random "slow downs".Was it due to the switch hardware, switch configuration, or device interference?Hard to say...I had a run of coax that was not being used.I ordered this EOC adapter hoping to get rid of the complications.I hooked them adapters together with a short piece of coax (to the "In" ports) to sync them.No need for an ethernet cable yet.10-20 seconds later they were sync'd.10-20 seconds to "lock" them.Powered everything down and moved both devices to their new homes.Plugged everything back up, including ethernet.Withing 30 seconds both devices were again sync'd and locked.Confirmed ethernet was working fine.Easy!I highly recommend!